Influence of stiffness of between-joists bracing on vibrational serviceability of wood floors.
Conference Proceeding
Khokhar, A., Chui, Y., & Smith, I. (2012)
Influence of stiffness of between-joists bracing on vibrational serviceability of wood floors. In P. Quenneville (Ed.), Proceedings of World Conference on Timber Engineering (WCTE 2012), 362-369
Floors with repetitive parallel wood joists overlain by wood panel sheathing behave as orthotropic two-way structures since their along-joist stiffness is much higher than acr...
3D-printing ‘Ocean plastic’–Fostering childrens’ engagement with sustainability
Journal Article
Vones, K., Allan, D., Lambert, I., & Vettese, S. (2018)
3D-printing ‘Ocean plastic’–Fostering childrens’ engagement with sustainability. Materials Today Communications, 16, 56-59. https://doi.org/10.1016/j.mtcomm.2018.04.001
Ocean plastic pollution has been identified as one of the biggest environmental threats of our time. As large islands of plastic waste such as the Pacific Gyre amass through t...
The effect of suspension bath composition on the composition, topography and structure of electrolessly deposited composite four-component Ni–W–P–ZrO2 coatings
Journal Article
Szczygieł, B., & Turkiewicz, A. (2008)
The effect of suspension bath composition on the composition, topography and structure of electrolessly deposited composite four-component Ni–W–P–ZrO2 coatings. Applied Surface Science, 254(22), 7410-7416. https://doi.org/10.1016/j.apsusc.2008.05.342
Composite four-component Ni–W–P–ZrO2 coatings were electrolessly deposited from a bath with different concentrations of aminoacetic acid (glycine—the complexing agent), sodium...
Design and Acoustic Performance of Building Constructions for Multi-Storey Housing: Compendium.
Book Chapter
Fausti, P., García, T. C., Ingelaere, B., Machimbarrena, M., Monteiro, C. R. A., Santoni, A., …Smith, S. (2014)
Design and Acoustic Performance of Building Constructions for Multi-Storey Housing: Compendium. In B. Rasmussen, & M. Machimbarrena (Eds.), COST Action TU0901 – Building acoustics throughout Europe. Volume 1: Towards a common framework in building acoustics throughout Europe, 213-244. COST European Cooperation in Science and Technology
This chapter provides an overview of the range of construction types
found across Europe to meet various sound insulation requirements for separating (party) walls and floors....
Preparation of flexible dielectric nanocomposites using nanocellulose and recycled alum sludge for wearable technology applications
Journal Article
Sun, D., Saw, L., Onyianta, A., 'rourke, Lu, Z., Wilson, C., …Shyha, I. (2022)
Preparation of flexible dielectric nanocomposites using nanocellulose and recycled alum sludge for wearable technology applications. Materials, Methods & Technologies, 16, 149-159
With the rapid development of wearable technology, flexible dielectric materials with environmental-friendly, low-cost and high-energy efficiency characteristics are in increa...
Experimental assessment of stiffness and damping in rubber-sand mixtures at various strain levels
Conference Proceeding
Bernal-Sanchez, J., Mcdougall, J., Barreto, D., Marinelli, A., Dimitriadi, V., Anbazhagan, P., & Miranda, M. (2019)
Experimental assessment of stiffness and damping in rubber-sand mixtures at various strain levels. In Earthquake Geotechnical Engineering for Protection and Development of Environment and Constructions, (1403-1410
The dynamic properties of shredded rubber-soil mixtures (ShRm), comprising a sub-rounded quartz sand combined with small rubber shreds at 0, 10, 20, 30% by mass, were investig...
Facilitators and benefits of implementing lean premise design: A case of Hong Kong high-rise buildings
Journal Article
Lam, E. W., Chan, A. P., Olawumi, T. O., Wong, I., & Kazeem, K. O. (2023)
Facilitators and benefits of implementing lean premise design: A case of Hong Kong high-rise buildings. Journal of Building Engineering, 80, Article 108013. https://doi.org/10.1016/j.jobe.2023.108013
Defective design, poor stakeholder participation, and a mismatch between design provisions and end-user requirements cause most building construction waste. However, lean buil...
Effective and Fast-Screening Route to Evaluate Dynamic Elastomer-Filler Network Reversibility for Sustainable Rubber Composite Design
Journal Article
Xia, T., Wemyss, A. M., Salehiyan, R., Heeley, E. L., Hu, X., Tang, F., …Wan, C. (2023)
Effective and Fast-Screening Route to Evaluate Dynamic Elastomer-Filler Network Reversibility for Sustainable Rubber Composite Design. ACS sustainable chemistry & engineering, 11, 17857-17869. https://doi.org/10.1021/acssuschemeng.3c06752
The introduction of self-healing and reprocessability into conventional vulcanized rubbers has been recognized as a promising strategy to promote elastomer circularity. Howeve...
Design for Additive Manufacturing and Finite Element Analysis of Fe-Mn Biodegradable Fracture Fixation Plate with Varying Porosity Levels
Conference Proceeding
Shaikh, M., Kahwash, F., Lu, Z., Alkhreisat, M., & Shyha, I. (2024)
Design for Additive Manufacturing and Finite Element Analysis of Fe-Mn Biodegradable Fracture Fixation Plate with Varying Porosity Levels. In Industrializing Additive Manufacturing: Proceedings of AMPA2023 (239-254). https://doi.org/10.1007/978-3-031-42983-5_17
Fracture fixation plates are osteosynthesis implants used to fix fractured bones in a human body. They are either left in the body or required to be removed after a bone heali...
Towards the Posthuman: Materiality and process in the creation of stimulus-responsive jewellery objects
Conference Proceeding
Vones, K. (2013)
Towards the Posthuman: Materiality and process in the creation of stimulus-responsive jewellery objects. In All Makers Now?
The idea of creating a jewellery organism that comes alive on the body has fascinated and inspired my research ever since learning about the potential inherent in smart materi...